Calculate tool costs per part: formula, service life and example

State:
AI-generated

Formula for tool costs per part

The simple shape divides the tool price into the usable cuttings and the parts that a cutting edge creates: A turning plate for 12 € with four cuttings costs 3 € per cutting edge; one cutting edge creates ten parts, costs 0.30 € cutting costs on each part.

The calculation is more precise about times, because parts per cutting edge are rarely directly known. The service life is the intervention time until the change, the intervention time per part comes from the processing time of the tool. The cutting costs come to the change: change time times cost set of the bound resources. Thus, the computer calculates tool costs per part of the app.

K_Part = tool price while cutting while cutting parts per cutting edge or K_Part = (K_Cut + t_change × hourly rate while 60) × t_intercept while T_Permanence

Not every machine minute consumes service life

For tool consumption, the intervention time of the tool considered counts. Machine life can also include rapid response, other tools, positioning and measuring. To use this total time as intervention time of a single milling machine would overestimate its consumption.

In the case of a turning plate, the purchase price is distributed to the actually usable cutting edges. Edges that cannot be used due to geometry or quality do not increase the usable number.

Calculation example with a insert

An assumed plate costs 12 € and has four usable cutting edges: 3 € per edge. The change takes two minutes and binds resources to 60 €/h, which means another 2 €. A service life costs 5 € including change.

At 30 minutes of service life and three minutes of operation time per part one tenth is used. The tool cost share is 0.50 € per part. This example describes computational consumption; breakage, entry parts or premature change due to the surface can increase the actual consumption.

K_Part = (K_Cut + t_change × hourly rate ÷ 60) × t_intervention ÷ T_resistance

Tool costs per part according to service life and intervention time

Example of calculation of this page: 5 € per service life including change (3 € cutting edge plus 2 minutes to 60 €/h).

Tool costs per part depending on service life and operating time. Example of calculation of this page: 5 € per service life including change (3 € cutting edge plus 2 minutes to 60 €/h).
Life T1 min procedure per part3 min procedure per part5 min procedure per part
15 min0,33 €1,00 €1,67 €
30 min0,17 €0,50 €0,83 €
45 min0,11 €0,33 €0,56 €
60 min0,08 €0,25 €0,42 €

K_Part = 5 € × intervention time ÷ Service life. Own plate prices, cutting number, change time and service life move all values in the same ratio.

Full tools and regrinds

In the case of a full tool, the calculator distributes purchase and specified post-grinding costs to the usable service life. A post-grind can achieve a different service life than the new tool. This relative service life is explicitly entered.

An additional holder price can be distributed to a specified number of cutting times. A holder portion is only additionally included in the invoice if it is not yet covered by another cost rate.

Economic service life as a limited model

The calculator also shows a theoretical economic service life from the Taylor approach. It requires an appropriate empirical exponent and unchanged boundary conditions. Dimensional stability, surface and breakage reliability can require an earlier change.

Therefore, cost optimization is not an instruction to run a tool up to a computationally optimal time. Compare the approach with the actual released switching criteria.

Sources and classification

Questions and answers

What is the formula for tool costs per part?

Without change time: Tool costs per part = tool price ÷ usable cutting ÷ parts per cutting edge. Expected times, as in the app's calculator: (costs per cutting edge + change time × cost set ṭ 60) × intervention time per part ÷ service life. With 12 € plate price, four cuttings, 2 minutes change to 60 €/h, 30 minutes service life and 3 minutes service life are the 3 € + 2 €) × 3 € 30 = 0.50 € per part.

Is tool change already included in the side-time?

This can be. If the full change time is already evaluated with the same resources in the cycle time per part, it must not be additionally set as a tool cost share.

Can I automatically choose the longest service life as the cheapest?

No. Lifetime, cutting speed, processing time and quality limits work together. The computer only evaluates the assumptions entered.

Tool costs per part in the CNC calculator app

Distributes cutting costs, regrinds and tool changes to the intervention time per part.

Free tool cost calculator per part in CNC Kalkulator with input and result
Calculate in the app

Free tools in your browser without sign-in

How the calculation from drawing, CAD model and your operating data looks like with you, we will gladly clarify on one of your parts: Book free first interview.

Carlo D'Este
D'Este Solutions

Welcome to the CNC Calculator

We will be happy to help you with any questions regarding the app, pro or your calculation.

Questions? Call us!