Laser cutting Calculate costs: cutting time, punctures and price per part

State:
AI-generated

Formula for laser cutting costs

The cost of a laser part consists of the machine time, the material and the proportion of setups and programming. The machine time consists of the pure cutting time over the contour length, the punctures at the beginning of each contour and the empty paths with positioning and handling.

The cutting speed depends on material, sheet thickness, laser power and cutting gas and comes from the cutting data sheet of the own plant or from measured orders. This page deliberately does not specify any table values for this.

Cutting time = contour length ÷ cutting speed + punctures × puncture time + empty distances Cost per part = cutting time × machine hourly rate + material incl. residual grid + set-up part

Contour length is only part of the runtime

Outer contours and all inner contours enter the cutting length. Insertion, short contours, travel paths, acceleration, sorting and removal cause additional time. A cut data value for a long straight contour is therefore not a measured average for the whole part.

In a DXF evaluation, open contours, double lines, units and assignment to cutting or engraving lines must be checked. The app helps with the geometric baseline values; it does not simulate laser control.

Calculate time from your own cut data

Example with freely selected operating data: 1,800 mm contour length at effective 3,000 mm/min results in 0.60 minutes. Twelve stitches with each 0.5 seconds add up to 0.10 minutes. With another 0.40 minutes for positioning and handling, 1.10 minutes per part are created.

At an assumed machine cost rate of 90 €/h, this corresponds to 1.65 € of time. Gas, material and set-ups are only added if they are not already included in the cost rate used.

t = L ו v + (number of punctures × seconds per injection) ו 60 + t_Alongside

Calculating example laser cutting per part

Calculating example laser cutting per part
PositionAdoptionInvoiceResult
Cutting time1,800 mm contour, 3,000 mm/min1.800 ÷ 3.0000.60 min
Insertions12 injections at 0.5 s12 × 0,5 ÷ 600,10 min
Empty routes and handlingAccepted–0,40 min
Machine time per part0,60 + 0,10 + 0,401.10 min
Time costs90 €/h Machine hourly rate1,10 × 90 ÷ 601,65 €
Material incl. residual gridCutting 200 × 150 mm, 3 mm steel, 25 % residual grid, 7.85 kg/dm³, 1.20 €/kg0.0375 m² × 3 mm × 7.85 × 1.201,06 €
Set-up percentage15 min Set up to 90 €/h on 50 parts22,50 € ÷ 500,45 €
Cost per part1,65 + 1,06 + 0,453,16 €

All inputs are freely chosen assumptions for the calculation path, no market prices and no cutting data of a particular plant. Gas, overhead costs and profit are not included.

Distribute material and equipment appropriately

The box picture determines which part of the plate is attributed to the order. The kilo price alone does not include any residual material or usable residual sheets. Rules for residual sheets and scrap credits should be the same for pre- and post-calculation.

Programme creation, installation and setup are per lot. For small quantities, this proportion may well exceed the average cost share.

Which values must come from the operation

Material and thickness specific cutting data, insertion times, gas consumption, plant availability and handling times are taken from released manufacturer data or measured own orders. This page does not provide a universal cutting value table.

Questions and answers

How do you calculate the cost of laser cutting?

Cutting time = contour length ÷ Cutting speed + punctures × cutting time + empty distances. The cutting time times machine hour rate results in the time costs; in addition, the material including residual grid and the set-up percentage per part. In the calculation example, 1.10 minutes at 90 €/h 1.65 € Time costs and with material and set-up 3.16 € per part.

Is one price per meter of cutting enough?

Only under comparable conditions. Sheet thickness, material, punctures and short contours can greatly change the effort. A meter price should specify its requirements.

Does the app automatically calculate the laser price from DXF?

The free app evaluates DXF geometry and calculates material, set-up and unit costs with your input. It does not promise an automatically determined laser price or a machine runtime from the controller.

Is there a laser cost calculator in the app?

The app does not currently have its own laser cutting tool. Contour length and contours are provided by the free DXF analysis, plate utilization and unit costs have their own computers; the cutting time is calculated using the formula of this page and the cutting data of your system.

Evaluate DXF contours in the CNC Calculator app

Determine length and individual closed surfaces from flat DXF contours.

Free analysis of DXF contours in CNC Kalkulator with input and result
Calculate in the app

Free tools in your browser without sign-in

How the calculation from drawing, CAD model and your operating data looks like with you, we will gladly clarify on one of your parts: Book free first interview.

Carlo D'Este
D'Este Solutions

Welcome to the CNC Calculator

We will be happy to help you with any questions regarding the app, pro or your calculation.

Questions? Call us!