Drilling: Dimensions H6 to H11
In the unit bore system, the bore is almost always an H-field: the lower dimension is on the nominal dimension, the upper one is on the basic tolerance IT above. The table mentions both dimensions in micrometers for all 13 nominal dimensions according to ISO 286.
Dimensions for holes H6 to H11 according to ISO 286
Upper / lower dimension in μm per nominal dimension range in mm.
| Nominal dimension (mm) | H6 | H7 | H8 | H9 | H10 | H11 |
|---|---|---|---|---|---|---|
| up to 3 | +6 / 0 | +10 / 0 | +14 / 0 | +25 / 0 | +40 / 0 | +60 / 0 |
| over 3 to 6 | +8 / 0 | +12 / 0 | +18 / 0 | +30 / 0 | +48 / 0 | +75 / 0 |
| over 6 to 10 | +9 / 0 | +15 / 0 | +22 / 0 | +36 / 0 | +58 / 0 | +90 / 0 |
| over 10 to 18 | +11 / 0 | +18 / 0 | +27 / 0 | +43 / 0 | +70 / 0 | +110 / 0 |
| over 18 to 30 | +13 / 0 | +21 / 0 | +33 / 0 | +52 / 0 | +84 / 0 | +130 / 0 |
| over 30 to 50 | +16 / 0 | +25 / 0 | +39 / 0 | +62 / 0 | +100 / 0 | +160 / 0 |
| over 50 to 80 | +19 / 0 | +30 / 0 | +46 / 0 | +74 / 0 | +120 / 0 | +190 / 0 |
| Over 80 to 120 | +22 / 0 | +35 / 0 | +54 / 0 | +87 / 0 | +140 / 0 | +220 / 0 |
| Over 120 to 180 | +25 / 0 | +40 / 0 | +63 / 0 | +100 / 0 | +160 / 0 | +250 / 0 |
| Over 180 to 250 | +29 / 0 | +46 / 0 | +72 / 0 | +115 / 0 | +185 / 0 | +290 / 0 |
| Over 250 to 315 | +32 / 0 | +52 / 0 | +81 / 0 | +130 / 0 | +210 / 0 | +320 / 0 |
| Over 315 to 400 | +36 / 0 | +57 / 0 | +89 / 0 | +140 / 0 | +230 / 0 | +360 / 0 |
| Over 400 to 500 | +40 / 0 | +63 / 0 | +97 / 0 | +155 / 0 | +250 / 0 | +400 / 0 |
At H, the lower dimension is always on the zero line; the number to the right of the slash is therefore 0, on the left is the basic tolerance IT. A nominal dimension at a range limit belongs to the lower range: Ø 30 mm belongs to "over 18-30".
Shafts: dimensions h6 to h11, g6, f7, k6, m6, n6, p6
In the case of waves, the letter determines the position to the zero line: h ends at the nominal dimension, g and f lie below and result in a H-bore game, k, m, n and p lie above and result in transition or excess. The number is the IT degree and thus the width of the field.
Dimensions for shafts h6 to h11, g6, f7, k6, m6, n6 and p6 according to ISO 286
Upper / lower dimension in μm per nominal dimension range in mm.
| Nominal dimension (mm) | h6 | h7 | h8 | h9 | h10 | h11 | g6 | f7 | k6 | m6 | n6 | p6 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| up to 3 | 0 / −6 | 0 / −10 | 0 / −14 | 0 / −25 | 0 / −40 | 0 / −60 | −2 / −8 | −6 / −16 | +6 / 0 | +8 / +2 | +10 / +4 | +12 / +6 |
| over 3 to 6 | 0 / −8 | 0 / −12 | 0 / −18 | 0 / −30 | 0 / −48 | 0 / −75 | −4 / −12 | −10 / −22 | +9 / +1 | +12 / +4 | +16 / +8 | +20 / +12 |
| over 6 to 10 | 0 / −9 | 0 / −15 | 0 / −22 | 0 / −36 | 0 / −58 | 0 / −90 | −5 / −14 | −13 / −28 | +10 / +1 | +15 / +6 | +19 / +10 | +24 / +15 |
| over 10 to 18 | 0 / −11 | 0 / −18 | 0 / −27 | 0 / −43 | 0 / −70 | 0 / −110 | −6 / −17 | −16 / −34 | +12 / +1 | +18 / +7 | +23 / +12 | +29 / +18 |
| over 18 to 30 | 0 / −13 | 0 / −21 | 0 / −33 | 0 / −52 | 0 / −84 | 0 / −130 | −7 / −20 | −20 / −41 | +15 / +2 | +21 / +8 | +28 / +15 | +35 / +22 |
| over 30 to 50 | 0 / −16 | 0 / −25 | 0 / −39 | 0 / −62 | 0 / −100 | 0 / −160 | −9 / −25 | −25 / −50 | +18 / +2 | +25 / +9 | +33 / +17 | +42 / +26 |
| over 50 to 80 | 0 / −19 | 0 / −30 | 0 / −46 | 0 / −74 | 0 / −120 | 0 / −190 | −10 / −29 | −30 / −60 | +21 / +2 | +30 / +11 | +39 / +20 | +51 / +32 |
| Over 80 to 120 | 0 / −22 | 0 / −35 | 0 / −54 | 0 / −87 | 0 / −140 | 0 / −220 | −12 / −34 | −36 / −71 | +25 / +3 | +35 / +13 | +45 / +23 | +59 / +37 |
| Over 120 to 180 | 0 / −25 | 0 / −40 | 0 / −63 | 0 / −100 | 0 / −160 | 0 / −250 | −14 / −39 | −43 / −83 | +28 / +3 | +40 / +15 | +52 / +27 | +68 / +43 |
| Over 180 to 250 | 0 / −29 | 0 / −46 | 0 / −72 | 0 / −115 | 0 / −185 | 0 / −290 | −15 / −44 | −50 / −96 | +33 / +4 | +46 / +17 | +60 / +31 | +79 / +50 |
| Over 250 to 315 | 0 / −32 | 0 / −52 | 0 / −81 | 0 / −130 | 0 / −210 | 0 / −320 | −17 / −49 | −56 / −108 | +36 / +4 | +52 / +20 | +66 / +34 | +88 / +56 |
| Over 315 to 400 | 0 / −36 | 0 / −57 | 0 / −89 | 0 / −140 | 0 / −230 | 0 / −360 | −18 / −54 | −62 / −119 | +40 / +4 | +57 / +21 | +73 / +37 | +98 / +62 |
| Over 400 to 500 | 0 / −40 | 0 / −63 | 0 / −97 | 0 / −155 | 0 / −250 | 0 / −400 | −20 / −60 | −68 / −131 | +45 / +5 | +63 / +23 | +80 / +40 | +108 / +68 |
At h, the upper dimension is on the zero line, g and f are below (game to hole H), k, m, n and p above (transition and excess). Further fields such as r6 or s6 are not included here.
Tolerance h11
The tolerance h11 is a wave field with the upper dimension 0 and the lower dimension −IT11, which means that the measure may only vary downwards. At Ø 20 mm, the wave is 0 / −130 μm, the shaft is between 19,870 and 20,000 mm.
h11 is a rough field, typical of drawn blank material, bolts without pass function and dimensions that have no leadership task.
Tolerance h9
The tolerance h9 also has the upper dimension 0, the lower dimension is −IT9. At Ø 20 mm the 0 / −52 μm is, the shaft is between 19,948 and 20,000 mm.
h9 is often found in drawn or ground rod material and in seats with moderate requirements; in the unit shaft system, the shaft h remains and the fit is created via the bore.
Tolerance H7
The tolerance H7 is the most common borehole: lower dimension 0, upper dimension +IT7. At Ø 20 mm, this is +21 / 0 μm, the borehole is between 20,000 and 20,021 mm.
With g6 H7 gives a sliding seat, with k6 a transition seat and with p6 a press seat. Game and oversize of these pairings for Ø 20, 50 and 100 mm shows the side to play fit, transition fit and oversize fit.
Match table as CSV for Excel
All values of both tables are available for download as a CSV file: one line per nominal dimension range and tolerance field with range limits, type (boring or shaft), upper and lower dimension and basic tolerance in μm. The file is separated with semicolon and UTF-8-coded and can be opened in Excel, LibreOffice or spreadsheet.
The CSV is created when the website is created from the same file as the tables on this page and as the pass calculator. It is not an Excel file with formulas, but a pure value table.
How to read the table
First, look for the nominal dimension range. ISO 286 reads the ranges as "over ... up to ...: Ø 20 mm belongs to more than 18 to 30 mm, Ø 30 mm also, Ø 30,5 mm already to more than 30 to 50 mm. Then read the two dimensions in the column of the tolerance field, above the upper one, below the lower dimension, both in micrometers.
For a hole Ø 20 H7 +21 and 0 μm, the maximum size is 20,021 mm and the minimum size is 20,000 mm; the difference is the tolerance of 21 μm. The tolerance of the maximum and minimum dimensions is shown by the side.
Maximum dimension = nominal dimension + upper dimension Minimum dimension = nominal dimension + lower dimension
Sources and classification
- ISO 286-1:2010 – ISO tolerance system for length dimensions, Part 1: Basics for tolerances, dimensions and fits
Basic tolerances and rules for the basic dimensions; in Germany as DIN EN ISO 286-1.
- ISO 286-2:2010 – ISO tolerance system for length dimensions, Part 2: Basic tolerances tables and boundary dimensions for drilling and shafts
Tables of boundary dimensions. The values of this page are derived from an own implementation (src/components/tools/iso286.ts), which the fit calculator also expects; for acceptances the standard text applies.
Questions and answers
What is the tolerance h11 at Ø 20 mm?
130 μm: upper dimension 0, lower dimension −130 μm. The shaft may be between 19,870 and 20,000 mm.
What does h9 mean in a wave?
The upper dimension is 0, the lower −IT9. At Ø 20 mm, this is −52 μm, at Ø 50 mm −62 μm. The shaft is thus never larger than the nominal dimension.
What dimensions does H7 have at Ø 50 mm?
Upper dimension +25 μm, lower dimension 0. The bore is therefore between 50,000 and 50,025 mm.
Is there the fit table as an Excel file?
As a CSV file that can be opened in Excel. It contains the same dimensions as the tables on this page, one line per nominal dimension range and tolerance field.
Why are fields such as r6 or s6 missing?
The tables only show fields that are stored and checked in the data on this website; the same data is used by the pass calculator. For further fields ISO 286-2 applies.


