Metric ISO rule thread M3 to M24 in numbers
The table summarises the dimensions that are most frequently searched for in construction and work preparation: slope P, core hole for thread cutting, flank diameter d₂, core diameter D₁ of the nut thread, core diameter d₃ of the screw and stress cross section Aₛ. The core holes are the usual drill diameters according to DIN 336. All other values are basic dimensions from the metric basic profile according to ISO 68-1, calculated using the same formulas as the app.
M24 has a 3 mm slope, a core hole of 21.0 mm and a cross-sectional stress of 352.5 mm²; M3 has a 0.5 mm slope and a 2.5 mm core hole. Basic dimensions do not include tolerance. For the limit dimensions of mother and bolt threads, the agreed tolerance class is also required. The core hole for thread profiles and the speed of the thread drill are available on the Calculate core hole page.
Metric ISO thread M3 to M24
Basic dimensions in mm, voltage cross-section in mm². Core hole for cut threads according to DIN 336; all other values calculated from d and P.
| Threads | Rising P | Corehole | Flank-Ø d2 | Core Ø D1 (mother) | Core Ø d3 (bolts) | Voltage cross section As |
|---|---|---|---|---|---|---|
| M3 | 0,5 mm | 2,5 mm | 2,675 | 2,459 | 2,387 | 5,0 mm2 |
| M4 | 0,7 mm | 3.3 mm | 3,545 | 3,242 | 3,141 | 8,8 mm2 |
| M5 | 0.8 mm | 4.2 mm | 4,480 | 4,134 | 4,018 | 14.2 mm2 |
| M6 | 1 mm | 5,0 mm | 5,351 | 4,918 | 4,773 | 20,1 mm2 |
| M8 | 1,25 mm | 6,8 mm | 7,188 | 6,647 | 6,466 | 36,6 mm2 |
| M10 | 1,5 mm | 8,5 mm | 9,026 | 8,376 | 8,160 | 58.0 mm2 |
| M12 | 1,75 mm | 10,2 mm | 10,863 | 10,106 | 9,853 | 84.3 mm2 |
| M14 | 2 mm | 12.0 mm | 12,701 | 11,835 | 11,546 | 115,4 mm2 |
| M16 | 2 mm | 14,0 mm | 14,701 | 13,835 | 13,546 | 156.7 mm2 |
| M20 | 2,5 mm | 17.5 mm | 18,376 | 17,294 | 16,933 | 244,8 mm2 |
| M24 | 3 mm | 21.0 mm | 22,052 | 20,753 | 20,319 | 352,5 mm2 |
Basic dimensions without tolerance, rounded to three places; the app shows two decimal places. Table books often round the voltage cross-section to whole mm², at M24 about to 353 mm² – it is the same size.
Basic dimensions of nominal diameter and slope
The ISO metric thread has a flank angle of 60°. The theoretical profile triangle is H = 0.866 × P high, and each diameter is given as a nominal diameter minus a fixed multiple of the slope. Therefore, for each metric thread, even for a fine thread or a special ascent, the two indications d and P.
The flank diameter d₂ is where the thread tooth and thread gap are the same width. Bolts and nuts are carried over it, and it is checked during three-thread measurement; the test value for this is calculated by the tool thread measurement app.
d₂ = d − 0.6495 × P D₁ = d − 1.0825 × P d₃ = d − 1.2269 × P
Corehole between table value and fist formula
For cut standard threads, the core hole is approximately equal to d - P. The values according to DIN 336 are rounded to usual drill diameters: For M8, the rough formula gives 6.75 mm, and drilling is done with 6.8 mm; for M12, 10.25 mm is converted into the usual 10.2 mm. The core hole is located above the basic dimension D₁, because the core diameter of the nut thread is tolerated upwards and a full profile depth would hardly bring any more load-bearing capacity, but would significantly stress the thread drill much more.
The material is displaced instead of machined, the core hole is larger. The app calculates as a benchmark d − 0.5 × P; the final hole determines the data sheet of the tool. The core hole from a desired carrying depth as well as the speed and feed of the thread drill is calculated by the thread calculator of this website.
Corehole (d) – P (cutting) Corehole (d) – 0.5 × P (forms)
Voltage cross section for the calculation of screws
The stress cross-section As is the computational cross-section with which the tensile load of a screw is evaluated. It is formed from the average of flank and core diameters and thus lies between both cross-sections. By multiplying the tensile strength, it results in the breaking force in the thread: strength class 8.8 stands for 800 N/mm² nominal tensile strength, with M10 with 58.0 mm² the approximately 46 kN.
The app has its own estimation calculator for minimum screw-in depth and tightening torque. Safety-relevant fittings still need a complete design.
Aₛ = π ÷ 4 × ((d₂ + d₃) ÷ 2)²
Fine thread with the same formulas
For fine threads, the pitch is specified in the designation, e.g. M10 × 1. When used in the formulas, d₂ = 9.350 mm, D₁ = 8.917 mm, d₃ = 8.773 mm and Aₛ = 64.5 mm² result; according to the empirical formula, the core hole is 9.0 mm. Compared to the standard thread M10 × 1.5, the profile is flatter, the core is thicker and the stress cross-section is about 11 percent larger.
In the production process, each slope needs its own tool. Thread drills are available in each diameter and slope, while a thread cutter covers several diameters of the same slope.
Customs thread: Convert slope to gears per inch
The conversion is a pure length conversion with 25,4 mm per inch: 20 gears per inch correspond to 1,27 mm incline, 1 mm incline corresponds to 25,4 gears per inch. The conversion calculator for threaded units in the app expresses nominal diameter and incline in full, its starting values 6,35 mm and 1,27 mm approximately as 0,25 inches and 20 TPI.
The same numbers do not mean exchangeability. Whitworth threads have a flank angle of 55° instead of 60°, and even at the same angle tolerance systems and designations of the double and metric threads differ. Therefore, the dimensions of the respective standard apply for inch threads; the app only converts the units.
TPI = 25,4 ÷ P [mm] P [mm] = 25,4 ÷ TPI
Questions and answers
Which slope is M24?
M24 is standardised in the standard thread with a 3 mm pitch. The core hole for cut threads is 21.0 mm, the flank diameter 22.052 mm and the stress cross-section 352.5 mm². Many tables round it to 353 mm²; the same size is meant.
Which slope is M3?
M3 has a normally thread of 0.5 mm slope. Drilled for a cut thread of 2.5 mm, the flank diameter is 2.675 mm and the voltage cross-section 5.0 mm².
Why is the tap drill diameter larger than the minor diameter D₁?
D₁ is the basic dimension of the mother thread without tolerance. The actual core diameter may be greater than this, and a full profile depth would hardly bring any more load-bearing capacity. Therefore, M8 is pre-drilled with 6.8 mm, although D₁ is 6.647 mm.
What is the flank diameter of a thread?
The diameter of a hypothetical cylinder on which the thread tooth and thread gap are equally wide. For metric threads, d₂ = d − 0.6495 × P, so 7.188 mm for M8 × 1.25. For example, it is checked on the outer thread using the three-thread method.
How large is the voltage cross section of M8, M10 and M12?
For the standard threads, the values are: M8 36.6 mm², M10 58.0 mm² and M12 84.3 mm². The values follow from Aₛ = π ÷ 4 × ((d₂ + d₃) ÷ 2)²; for other sizes and fine threads, the app calculates them based on diameter and pitch.
How do I calculate gears per inch in millimetre incline?
A slope in mm = 25.4 ÷ gears per inch. 13 gears per inch give 1,954 mm, 20 gears per inch 1.27 mm. Profile, flank angle and tolerance are further determined by the inch thread standard.
Does the thread table contain tolerances?
No. All values are basic dimensions without tolerance class. For limit dimensions the agreed thread standard and tolerance class apply, for metric threads often 6H for the nut and 6g for the bolt thread.


