General tolerances according to ISO 2768: Table and calculator

State:
AI-generated

ISO 2768-1 assigns a permissible deviation per tolerance class to each nominal dimension range. For 100 mm, class m ±0.3 mm, class f ±0.15 mm and class c ±0.8 mm apply. The calculator also shows the limit dimensions and angle tolerance.

Calculate general tolerance

Permissible deviation according to ISO 2768 for length and angle dimensions

The result is updated every time you enter it.

Formulas

Grenzmaße = Nennmaß ± Toleranz

Permissible area

The tolerance depends on the nominal range and the class.

Toleranzfeld = 2 × Abmaß

Total width

Relevant for process capability and measuring device selection.

Limit dimensions for length dimensions according to ISO 2768-1

Permissible deviations in millimetres per nominal dimension range and tolerance class.

Limit dimensions for length dimensions according to ISO 2768-1. Permissible deviations in millimetres per nominal dimension range and tolerance class.
Nominal dimension range (mm)F – finem – mediumc – coarsev – very rough
0,5 to 3±0,05±0,1±0,2–
over 3 to 6±0,05±0,1±0,3±0,5
over 6 to 30±0,1±0,2±0,5±1
Over 30 to 120±0,15±0,3±0,8±1,5
Over 120 to 400±0,2±0,5±1,2±2,5
Over 400 to 1000±0,3±0,8±2±4
over 1000 to 2000±0,5±1,2±3±6

ISO 2768-2 with Classes H, K and L applies to form and position tolerances, where the concentricity is 0.1, 0.2 and 0.5 mm respectively.

ISO 2768-1

General tolerance for angles according to ISO 2768-1

Angle tolerances according to ISO 2768-1 do not depend on the angular value, but on the length of the shorter leg. The table indicates the permissible deviation for angular dimensions without specifying its own tolerance.

General tolerance for angles according to ISO 2768-1. Angular tolerances according to ISO 2768-1 do not depend on the angular value, but on the length of the shorter leg. The table shows the permissible deviation for angular dimensions without the tolerance.
Length of the shorter leg (mm)f – fine and m – mediumc – coarsev – very rough
up to 10±1°±1°30′±3°
Over 10 to 50±0°30′±1°±2°
Over 50 to 120±0°20′±0°30′±1°
Over 120 to 400±0°10′±0°15′±0°30′
over 400±0°5′±0°10′±0°20′

The angle tolerance applies to the position of the lines or mantle lines, not to the shape deviation of the surfaces.

ISO 2768-1

Limit dimensions for roundings and threads according to ISO 2768-1

Permissible deviation in mm for outer radii and chamfer heights without own tolerance.

Limit dimensions for roundings and threads according to ISO 2768-1. Permissible deviation in mm for outer radii and thread heights without own tolerance.
Radius or nose height (mm)F – finem – mediumc – coarsev – very rough
0,5 to 3±0,2±0,2±0,4±0,4
over 3 to 6±0,5±0,5±1±1
over 6±1±1±2±2

Broken edges have a separate table with only three areas; a fase 0,5 × 45° may vary by ±0.2 mm in class m.

ISO 2768-2

Form and position tolerances according to ISO 2768-2

General tolerances in mm for features without own shape or position tolerance, ordered by nominal dimension range and tolerance class.

Form and position tolerances according to ISO 2768-2. General tolerances in mm for features without own shape or position tolerance, ordered by nominal dimension range and tolerance class.
Characteristic and nominal dimension range (mm)HKL
Straightness and flatness up to 100,020,050,1
Straightness and flatness over 10 to 300,050,10,2
Straightness and flatness over 30 to 1000,10,20,4
Straightness and flatness over 100 to 3000,20,40,8
Straightness and flatness over 300 to 10000,30,61,2
Straightness and flatness over 1000 to 30000,40,81,6
Right angle up to 1000,20,40,6
Rectangularity over 100 to 3000,30,61
Rectangularity over 300 to 10000,40,81,5
Perpendicularity over 1000 to 30000,512
Symmetry up to 1000,50,60,6
Symmetry over 100 to 3000,50,61
Symmetry over 300 to 10000,50,81,5
Symmetry over 1000 to 30000,512
Run (round and flat)0,10,20,5

For straightness the length of the line, for flatness the longer side of the surface, for right-angleness the shorter thigh counts. Reference rules and details set ISO 2768-2.

All four tables are available as a file to print out or for spreadsheets: Download general tolerances ISO 2768 as CSV. Without registration and without form.

Form and location

General tolerance for position, coaxiality and concentration

Position without own position tolerance

A general tolerance for position does not include ISO 2768-2. Without position tolerance, the position of a bore is determined over its coordinate dimensions, and these fall under the length tolerances according to ISO 2768-1, in class m for example ±0.3 mm for coordinates over 30 to 120 mm. This results in an angular tolerance zone, the size of which depends on the dimension chain.

Where the position counts for the assembly, a position tolerance according to ISO 1101 with reference system belongs to the drawing. For the offer the difference is important: a real position tolerance requires a measurement in the reference system, a coordinate dimension only the individual length dimensions.

Coaxiality and concentration

For coaxiality and concentration, ISO 2768-2 does not specify any specific value. The deviation may be as large as the general running tolerance, i.e. 0.1 mm in class H, 0.2 mm in class K and 0.5 mm in class L.

A bearing seat or a centering usually needs more than this limit. Then a separate running or coaxiality tolerance belongs to the characteristic, and the general tolerance applies only to the other surfaces.

Form and location

What ISO 2768-2 also regulates

Roundness, cylinder shape and parallelity

For roundness, the numerical value of the diameter tolerance applies in general, but at most the running tolerance of the respective class. Parallelity is limited to dimensional tolerance or straightness or flatness tolerance, depending on which value is greater. ISO 2768-2 does not refer to a specific value for the cylinder shape; it consists of roundness, straightness and parallelity.

The note in the field of writing

A combined note such as ISO 2768-mK: class m for length and angular dimensions, class K for shape and position. With the addition E, i.e. ISO 2768-mK-E, the envelope condition applies additionally for all individual dimensions. For the geometric part ISO 22081 is the successor; the decisive factor is what is on the concrete drawing.

Example

See general tolerances on a rotary part

Example: ISO 2768-mK on a rotary part drawing

A bolt is 85 mm long, has a heel of Ø 12 mm to 30 mm length and a chamfer of 0.5 × 45°. ISO 2768-mK stands in the title block, with none of these dimensions having its own tolerance.

The total length 85 mm is in the range of 30 to 120 mm: Class m allows ±0.3 mm, i.e. 84.7 to 85.3 mm. The diameter 12 mm is in the range of 6 to 30 mm: ±0.2 mm, i.e. 11.8 to 12.2 mm. The heel length 30 mm still belongs to the range of 6 to 30 mm and also receives ±0.2 mm. The own line for roundings and bevels applies to the bevel height 0.5 mm: ±0.2 mm in class m. The 45° angle has a shorter leg under 10 mm and therefore may vary by ±1°.

Class K limits the rotation of the heel to 0.2 mm. For a bearing seat this is usually not enough; then a tolerance of its own belongs to the measure, and the general tolerance applies only to the rest.

Standard level

Status of the standard

Expenditure and successors

ISO 2768-1 for length and angular dimensions is still available in the 1989 edition. ISO 2768-2:1989 for form and position has withdrawn ISO 2021; successor for general geometric specifications is ISO 22081:2021, which works with a reference system instead of with classes H, K and L.

For existing drawings this does not change anything: A note such as ISO 2768-mK applies as it stands on the drawing and is agreed with the customer. For the offer the note of the concrete drawing counts, not the latest standard.

The note in the title block tolerates the whole component

General tolerances apply to each measure without its own indication. A finer class therefore does not cost a characteristic, but the entire processing and testing.

Questions and answers

What does ISO 2768-m mean?

Tolerance class m for length and angular dimensions without specification of tolerance. For a dimension of 100 mm the ±0.3 mm, for 30 mm ±0.2 mm and for 400 mm ±0.5 mm.

What classes are there?

f for fine, m for medium, c for coarse and v for very coarse. For form and position tolerances ISO 2768-2 supplements classes H, K and L; a combined note such as ISO 2768-mK is common.

How is angle tolerance determined?

Not above the angular value, but above the length of the shorter leg. Up to 10 mm apply in class m ±1°, to 50 mm ±0°30′, to 120 mm ±0°20′ and to 400 mm ±0°10′.

What does ISO 2768-mK mean?

The note combines class m for length and angular dimensions according to ISO 2768-1 with class K for shape and position tolerances according to ISO 2768-2. If there is also an E behind it, i.e. ISO 2768-mK-E, the envelope condition applies to all individual dimensions.

Which general tolerance applies to a position?

ISO 2768-2 does not specify a general tolerance for position. Without position tolerance, the position of a bore is only obtained over the coordinate dimensions, and these fall under the length tolerances according to ISO 2768-1, in class m for example ±0.3 mm for 30 to 120 mm. Functionally important layers belong to the drawing as position tolerance according to ISO 1101.

Which general tolerance applies to coaxiality and concentration?

ISO 2768-2 does not specify a specific value. The deviation may be as large as the general running tolerance in the limit case: 0.1 mm in Class H, 0.2 mm in Class K and 0.5 mm in Class L.

What does ISO 2768-mH mean?

Class m for length and angular dimensions as in mK, but the finer class H for shape and position. The concentric course is then limited to 0.1 mm instead of 0.2 mm, for example, the flatness of an 80 mm long surface to 0.1 mm instead of 0.2 mm.

What applies to old drawings with DIN 7168?

DIN 7168 is the withdrawn predecessor of the general tolerances. The class must be read as it stands on the drawing; whether the values of a current ISO-2768 class correspond to, is checked for the offer and confirmed in case of doubt with the customer, instead of implicitly changing.

How much does a finer class cost?

The jump from m to f halves the permissible deviation in all not individually tolerated dimensions. This means tighter process control, more levelling, additional measuring points and a higher reject risk – across the entire component.

What if there is no note?

The acceptance should be documented and asked as a question instead of tacitly meeting it. ISO 22081 exists as the successor standard for the geometric part.

Sources

Tolerance calculator in the CNC Calculator app

ISO fits, general tolerances, surfaces and tolerance chains.

Range tolerances in the CNC Kalkulator
Open tolerances area

Free tools in your browser without sign-in

As from "General tolerances according to ISO 2768: Table and calculator with geometry, drawing requirements and your cost rates becomes an offer, we are happy to clarify personally: Book free first interview.

Carlo D'Este
D'Este Solutions

Welcome to the CNC Calculator

We will be happy to help you with any questions regarding the app, pro or your calculation.

Questions? Call us!