Stainless steel grades in cut data finder
The app lists four stainless steels from the ISO group M with its own cutting data: 1.4301 (X5CrNi18-10, V2A, AISI 304), 1.4404 (X2CrNiMo17-12-2, V4A, AISI 316L), 1.4305 (X8CrNiS18-9, AISI 303) and the martensitic 1.4057 (X17CrNi16-2, AISI 431). In the material database of the app, you can also find these types via the alias names, such as V2A or 316L.
The app's hints summarize the behavior: 1.4301 solidifies when the cutting edge rubs, the chip thickness must not become too small. 1.4404 is tougher than 1.4301 and forms long chips, sharp cutting and cooling are important. 1.4305 is sulfurized and thus the best machined austenitic variety. 1.4057 is remunerated and tougher than the austenitic varieties.
Start values for milling, turning and drilling
The areas are starting values from the cut data finder of the app for coated carbide. The tooth feed applies to a 10 mm diameter cutter, the drill feed for a 10 mm drill; when turning f is the feed per revolution. The data of your tool manufacturer is binding.
- 1.4301: milling vc 80–140 m/min, fz 0,04–0.07 mm; turning vc 120–200 m/min, f 0.12–0.35 mm; drilling vc 50–90 m/min, f 0.08–0.18 mm
- 1,4404: milling vc 70–130 m/min, fz 0,04–0.07 mm; turning vc 110–180 m/min, f 0,12–0.30 mm; drilling vc 45–80 m/min, f 0,08–0.16 mm
- 1,4305: milling vc 90–160 m/min, fz 0,04–0.08 mm; turning vc 140–230 m/min, f 0,12–0.35 mm; drilling vc 60–100 m/min, f 0,10–0,20 mm
- 1,4057: milling vc 70–120 m/min, fz 0,03–0.06 mm; turning vc 100–170 m/min, f 0,10–0,30 mm; drilling vc 40–75 m/min, f 0,08–0,15 mm
- Specific cutting force kc1.1: 2,100 N/mm² (1.4305), 2,300 N/mm² (1.4057), 2,350 N/mm² (1.4301), 2,400 N/mm² (1.4404)
Cold solidification and chipping thickness
Austenitic stainless steel does not forgive too thin chips. When milling with a small cutting width, the chip becomes thinner than the tooth feed suggests. Cutting data Milling compensates for this chip thinning and lifts the tooth feed until the maximum chip thickness returns to the catalogue value. Without compensation, the cutting edge rubs, the surface solidifies and the next tooth cuts into harder material.
The cutting force also reacts to thin chips. According to Kienzle, the specific cutting force increases by a factor of 2^mc with half chip thickness; mc 0.21 is about 16%. The cutting force calculator of the app calculates the stored values for each variety.
kc = kc1.1 × h^(−mc)
Varieties without own entry: 1.4571, 1.4307 and duplex
The app’s material database lists density and standards for many common grades. Where a grade has no cutting-data entry, the catalogue points to the closest grade: 1.4307 and 1.4541 to 1.4301, 1.4401 and 1.4571 to 1.4404, the sulphur-containing grades 1.4104 and 1.4005 to 1.4305, and 1.4021 to 1.4057.
For Duplex 1.4462, Lean Duplex 1.4362 and Superduplex 1.4410, the catalogue also refers to 1.4404, with the explicit indication that the cutting speed is significantly reduced due to higher strength. The app does not mention its own numbers for Duplex; here the data of the tool manufacturer applies. For the 1.4542 (17-4), the catalog refers to 1.4057 and advises to check the heat treatment condition before processing.
Time supplement and service life compared to structural steel
With identical tool and intervention, diameter 10 mm milling cutter with three cutting edges, 10 mm cutting depth and 5 mm cutting width, the app's starting values deliver the following cutting times for 100 cm³ chip volume: S235JR 1.5 minutes, C45 2.2 minutes, 1.4305 2.8 minutes, 1.4301 3.5 minutes and 1.4404 3.8 minutes. Compared to structural steel, 1.4301 takes 2.3 times, 1.4404 times 2.5 times and 1.4305 takes just under double.
When turning lengthwise with the pre-setting of cutting data Turning, Ø 50 mm, 100 mm cutting length and 2 mm cutting depth, a cut in S235JR takes 13 seconds, in 1.4301 26 seconds and in 1.4404 32 seconds.
The cutting speed is easy to increase, it costs life. With the Taylor exponent 0.25, the pre-setting of the service life calculator, a 20 % higher cutting speed halves the service life approximately. Use the exponent from your own measurements; the effect on the cost shows the computer tool costs per part.
T₂ = T₁ × (vc₁ ÷ vc₂)^(1/n)
Questions and answers
Which cutting speed applies to V2A during milling?
For 1.4301 (V2A), the app's cutting data finder specifies 80 to 140 m/min with starting value 110 m/min and a tooth feed of 0.04 to 0.07 mm for a 10 mm diameter cutter. When turning, it is 120 to 200 m/min.
Which values apply to 1.4571?
1.4571 does not have its own cutting data in the app. The material catalog refers to 1.4404; its starting values are 100 m/min when milling and 145 m/min when turning. This is an approximation, the manufacturer specifications have priority.
How do I chip Duplex 1.4462?
The app does not mention any numbers for Duplex. The catalog refers to 1.4404 and points out that the cutting speed is significantly reduced due to the higher strength. Use the cutting data of your tool manufacturer and calculate the service life and tool costs separately.
How much longer does the machining of stainless steel take compared to structural steel?
With the same milling cutter and intervention, the start values of the app for 1.4301 are 2.3-fold and for 1.4404 the 2.5-fold of the main time of S235JR. Shorter service life and more frequent tool changes are added.


