Titanium cutting: cutting data, service life and tool costs at Ti-6Al-4V

State:
AI-generated

Ti-6Al-4V in the cut data finder

The app includes Ti-6Al-4V (TiAl6V4, Grade 5, material number 3.7165) in the ISO Group S with its own cutting data. It has a density of 4.43 g/cm³, a tensile strength of 900 to 1,000 N/mm², a elasticity module of 114 GPa and a thermal expansion of 8.6 μm/(m·K). The app's hint: poor heat conduction, therefore low cutting speed, high coolant quantity and no dwell times.

Reintitan Grade 2 (3.7035) and Ti-6Al-4V ELI (Grade 23) are included in the app's material database with their own density; for cutting data, the catalog refers to Ti-6Al-4V. For Grade 2, it adds that Reintitan tends to stick to the cutting edge and needs sharp cutting and plenty of cooling.

Start values for milling, turning and drilling

The values are starting values from the cutting data finder in the app for coated hard metal; the data of your tool manufacturer are binding. For a milling cutter with a diameter of 10 mm, the starting value of 60 m/min results in around 1,910 1/min, with three cuts and fz 0.045 mm a feed speed of around 260 mm/min. When turning longitudinally with the pre-settings of cutting data Turning, Ø 50 mm, 100 mm cutting length and 2 mm cutting depth, a cut with the starting values takes around 79 seconds, in C45 around 17 seconds.

  • Specific cutting strength: kc1.1 = 1,450 N/mm², mc = 0.23

Starting values for milling, turning and drilling: Ti-6Al-4V and C45

Starting values for milling, turning and drilling: Ti-6Al-4V and C45
Procedurevc areaStart value vcFeed (start value)C45 for comparison
Milling, Ø 10 mm40–80 m/min60 m/minfz 0.03–0.06 mm (0.045 mm)vc 160 m/min, fz 0,06 mm
Rotate50–90 m/min70 m/minf 0,1–0,25 mm (0,175 mm)vc 205 m/min, f 0,275 mm
Drilling, Ø 10 mm25–50 m/min37.5 m/minf 0,06–0,12 mm (0,09 mm)vc 95 m/min, f 0,185 mm

Starting values from the cut data finder of the app for coated carbide, each center of the range; fz per tooth, f per turn. The data of the tool manufacturer are binding.

Heat at the cutting edge instead of cutting force

Titanium needs less cutting force than steel. At 0.1 mm chip thickness, the specific cutting force with the values of the app is around 2,460 N/mm², at C45 around 3,060 N/mm². A kilowatt drive power generates around 19.5 cm³/min in titanium at 80% efficiency and 15.7 cm³/min in C45.

Nevertheless, the cutting speed is less than half. The heat remains at the cutting edge because of the poor heat conduction, rather than flowing off with the chip. In the NC program, this means: even operation, sufficient coolant and no resting of the tool in the average.

Tool costs per part as a price driver

In a comparative case with a diameter of 10 mm, three cutting edges, 10 mm cutting depth and 5 mm cutting width, the starting values of the app for Ti-6Al-4V are around 13 cm³/min, for C45 around 46 cm³/min. For 100 cm³ chip volume, the 7.8 instead of 2.2 minutes of operation time, the 3.5 times.

The calculator distributes tool costs per part cutting costs and change time after intervention time. With its sample values, turning plate 12 € with four cuttings, 2 minutes change time, 60 €/h and 30 minutes service life, a part with 3 minutes operation costs 0.50 € tool. If the intervention time increases as compared to 3.5 times and the service life of the cutting edge halves, which here serves only as an assumption, it becomes 3.50 € per part, i.e. seven times.

The service life reacts strongly to the cutting speed. With the pre-set Taylor exponent 0.25, a 10 % higher cutting speed costs around a third of the service life. For titanium, use exponent and reference life from your own tests or manufacturer's specifications.

K_Part = (K_Cut + t_change × minute set) × t_intercept ÷ T

Calculate Titanium Parts

For a robust offer, the tool costs for titanium as its own position are included in the calculation, not in a flat-rate material surcharge. The intervention time comes from cutting data milling or turning with the starting values or your catalog values, the service life from the own recalculation.

The low density of the stock helps: With 4.43 g/cm³, a titanium stock weighs about 44% less than a steel stock of the same volume. You use the kilo price for titanium semi-finished products from your supplier's offer; the app calculates stock weight and material costs.

If a stock of Grade 5 is sawn by the rod after drawing, the cutting into the calculation also belongs: saw time and saw addition calculate the side saw time, the material number 3.7165 and the density are in the material database.

Questions and answers

What is the cutting speed for Titan Grade 5?

For Ti-6Al-4V, the cut data finder of the app calls 40 to 80 m/min with starting value 60 m/min, 50 to 90 m/min turning and 10 mm drilling 25 to 50 m/min. The values apply to coated carbide.

Do the values apply to Reintitan Grade 2?

Grade 2 (3.7035) does not have its own cutting data in the app; the material catalog refers to Ti-6Al-4V. It adds that pure titanium glues to the cutting edge and needs sharp cutting as well as plenty of cooling. The manufacturer's specifications are binding.

Why is titanium expensive to cut, even though the cutting force is lower?

Because the heat at the cutting edge limits the cutting speed. With the app's starting values, the same chip volume lasts about 3.5 times as long as in C45, and the cuttings wear faster. Both have a multiplicative effect on the tool costs per part.

How do I calculate the tool costs per titanium part?

In the calculator, you enter the cost of tools per part, the price of plates or tools, usable cutting, service life, time of intervention per part, change time and cost rate. The app distributes cutting and change costs after operation time and additionally shows the economic service life according to Taylor.

Cut Data Finder in the CNC Calculator App

Shows the recommended areas for cutting speed and feed with start, minimum and maximum value to the material, process and tool.

Free cutting data finder in the CNC Kalkulator with input and result
Calculate in the app

Free tools in your browser without sign-in

How the calculation from drawing, CAD model and your operating data looks like with you, we will gladly clarify on one of your parts: Book free first interview.

Carlo D'Este
D'Este Solutions

Welcome to the CNC Calculator

We will be happy to help you with any questions regarding the app, pro or your calculation.

Questions? Call us!